License number EC13001410

Why Your Circuit Breaker Keeps Tripping (And When to Call an Electrician)

A breaker that trips is doing exactly what it was installed to do. It is a safety device, and it has just decided that something on that circuit was dangerous enough to cut the power. The question is not how to stop it tripping. The question is what it is protecting you from. Most of the time the answer is harmless and you can sort it out yourself in ten minutes. Sometimes it is a warning you should not reset past. This page covers both, and how to tell them apart. Breaker tripping immediately, hot to the touch, or accompanied by a smell? Call 561-582-2600 now.

Electrical distribution panel with circuit breakers, wiring, and control components.
Large electrical distribution panel with circuit breakers, fuse holders, and control modules.

Stop Here If Any of These Are True

Do not keep resetting the breaker if you notice any of the following. Leave it off and call.

  • The breaker trips the instant you reset it, with nothing plugged in on that circuit.
  • You can smell burning plastic, or see scorch marks or discoloration on the breaker, the panel or an outlet.
  • The breaker, the panel door or an outlet is warm or hot to the touch.
  • The panel is buzzing, crackling or popping.
  • The breaker handle feels loose, mushy, or will not stay in the on position.
  • It is the main breaker rather than a branch circuit breaker.

Each of those means something is failing rather than something is overloaded, and repeatedly forcing power back into a failing circuit is how an electrical problem becomes a fire.

How a Breaker Works, Briefly

Worth thirty seconds because it explains everything that follows.

A breaker has two separate mechanisms. A thermal one responds slowly to sustained current above its rating, which is what catches an overload: too much plugged in, drawing too much, for long enough to heat the strip inside. A magnetic one responds almost instantly to a very large surge, which is what catches a short circuit.

That difference is your best diagnostic tool, and it costs nothing. A breaker that trips after several minutes of use is behaving like an overload. A breaker that trips the instant you switch it on is behaving like a short or a ground fault. Those two point at completely different problems.

Electrical control panel with organized wiring, automation modules, and circuit protection devices.

The Five Common Causes

1. Overloaded circuit

The most common cause and the least serious. Too many things drawing power on one circuit at once. Classic culprits are space heaters, hair dryers, microwaves, coffee makers, window units and anything with a heating element. Typically the breaker holds for a while and then trips, and it happens at the same time of day or when the same combination of things is running.

2. Short circuit

A hot conductor touching a neutral, inside the wiring, a device or an appliance. This produces a large instantaneous current and the breaker trips immediately, often with a bang, a flash, or a smell. A short is not a nuisance, it is a fault, and it needs finding rather than resetting.

3. Ground fault

A hot conductor finding a path to ground, through a metal box, damp insulation, or water. Extremely common in this climate. It also trips instantly, and it is what GFCI devices in kitchens, bathrooms, garages, outdoors and around pools are specifically built to catch.

4. A faulty appliance

Something plugged in has an internal fault. Worth checking before anything else, because it is free. Unplug everything on the circuit, reset, then reintroduce items one at a time. If the breaker trips the moment one particular thing goes back in, you have found it, and the fix is an appliance repair rather than an electrician.

5. The breaker itself has failed

Breakers wear out. The internal mechanism weakens with age, heat and repeated tripping, and a worn breaker starts tripping below its rating, sometimes at random. This is common in panels over twenty-five years old and in hot, humid, salt-air environments, which describes most of South Florida. A breaker that has tripped many times is a breaker that is closer to failing.

Diagnosing It Yourself in Ten Minutes

  1. Note the pattern. Does it trip immediately, or after a while? At a particular time of day? Only when something specific is used?
  2. Unplug everything on the circuit, including things that are switched off but still plugged in.
  3. Reset the breaker properly. Push the handle fully to off first, then firmly to on. A breaker left halfway between will not reset, which is the cause of a lot of unnecessary phone calls.
  4. If it holds with nothing plugged in, plug items back one at a time, leaving a few minutes between. If one item trips it instantly, that item is the problem. If it trips only once several things are running, the circuit is overloaded.
  5. If it trips immediately with nothing plugged in, stop. The fault is in the wiring, a device, or the breaker itself, and that is where this becomes our job.

That sequence resolves a large share of tripping breakers without anybody paying for a visit, and we would rather you tried it.

Exposed electrical wires and tangled cables inside an unfinished wall junction box.

What the Specific Symptom Tells You

It trips immediately with nothing plugged in

A short circuit, a ground fault in the fixed wiring, or a failed breaker. Not an overload, since there is nothing drawing current. This needs testing to locate, and it should not be left on.

It started all of a sudden with no change in use

Points away from overload and toward something that changed on its own: a connection that has worked loose, insulation that has degraded, water that has found its way in, or a breaker reaching the end of its life. In this part of the world it is also worth checking whether a recent storm or heavy rain preceded it.

It only trips when I plug something in

Almost always the appliance. Test the item on a different circuit. If it trips that one too, the appliance is faulty.

It trips in one room only

Narrows it to that circuit, which is useful. The cause is a fault in that run of wiring, a device on it, or simply too much load concentrated there.

The breaker will not reset at all

Either the fault is still present and the breaker is tripping again faster than you can see, or the breaker has failed internally. Try the full off-then-on reset once. If it still will not hold, leave it off.

The main breaker keeps tripping

Treat this as serious. A main trips when the whole service is overloaded, when there is a fault on the supply side of the distribution, or when the main breaker itself is failing. It is not a nuisance and it should not be repeatedly reset. Call.

The breaker or panel is hot

Heat means resistance, and resistance in a panel means a loose or deteriorating connection that is burning energy as heat inside a closed metal box. This is one of the few electrical symptoms that genuinely warrants a call the same day.

GFCI and AFCI Breakers Trip for Different Reasons

If the device is a GFCI or AFCI breaker, or the circuit runs through a GFCI outlet, the rules change.

GFCI protection trips on tiny imbalances between hot and neutral, in the milliamp range, because that is the level at which current leaking through a person becomes dangerous. In this climate they trip on moisture constantly: outdoor outlets after rain, pool and spa equipment, condensation in an outdoor disconnect, a bathroom circuit in summer. Sometimes the device itself has simply aged, since GFCIs have a finite life and should be tested periodically.

AFCI protection trips on the electrical signature of arcing. It is genuinely useful, and it is also the one people complain about most, because some older appliances and certain motors produce signatures it reads as arcing. A nuisance-tripping AFCI should still be investigated rather than swapped for a standard breaker, because occasionally it is detecting exactly what it was designed to detect.

The South Florida Causes Nobody Mentions

Most pages on this subject are written for a general audience. These are the ones we actually find here.

  • Air conditioning. Condensers and air handlers are the biggest loads in most homes here and they run most of the year. A failing compressor, a bad capacitor or a motor drawing locked-rotor current will trip its breaker, and it often presents as a breaker problem rather than an AC problem.
  • Pool and spa equipment. Pumps, heaters and lighting live outdoors in wet conditions on GFCI protection, which is exactly the recipe for repeated tripping as seals and insulation age.
  • Humidity and salt air. Moisture gets into outdoor boxes, disconnects and fixtures, and salt accelerates corrosion on terminations. Both produce ground faults that appear and disappear with the weather.
  • Pests. Ants in particular nest inside outdoor disconnects, pool equipment housings and junction boxes, and they cause faults that make no sense until somebody opens the box and looks.
  • Storm damage. Water that got in during a storm can cause faults days or weeks later, once it has worked into a connection.
  • Old panels in hot garages. A panel on an unconditioned garage wall in South Florida lives a hard life, and breakers in it age faster than the same breakers would in a cooler climate.

When the Panel Is the Real Problem

Sometimes the breaker is a symptom of something larger.

If your panel is full, if the house is still on 100 amp service while running modern loads, or if circuits are routinely carrying more than they were designed for, then tripping breakers are the system telling you it has run out of capacity. Replacing a breaker does nothing for that, and adding circuits to a full panel is not possible without a sub-panel or an upgrade.

There is also the opposite and more serious problem. Federal Pacific Stab-Lok and Zinsco panels have a documented history of breakers failing to trip when they should, which is the dangerous failure rather than the annoying one. If you have one of those panels, the conversation is not about this breaker. Our [Federal Pacific (FPE) Panel Replacement] page covers it.

We will tell you honestly which situation you are in. A single worn breaker in a sound panel is a small job, and we would rather do the small job than sell you a panel you do not need.

What Breaker Repair Costs

Job

Typical range*

Diagnostic visit to trace a tripping circuit

$125 to $250

Replace a standard single-pole breaker

$150 to $300

Replace a double-pole or higher-amp breaker

$200 to $450

Replace a GFCI or AFCI breaker

$200 to $400

Repair a fault found in the wiring

Quoted after diagnosis

Obsolete or discontinued panel breakers

Quoted. Availability is the issue, not labor

After-hours or emergency visit

Higher. Quoted before dispatch

*Planning estimates. The variable that matters most is whether the breaker is the problem or merely the messenger: replacing a breaker is quick, while finding an intermittent ground fault in concealed wiring is the part that takes time.

We tell you the diagnostic charge before coming out, and the repair price after we have found the fault and before we fix it.

Why West Palm Beach Calls Nassif Electric

  • Fifty years in South Florida, since 1976.
  • Florida statewide licensed unlimited electrical contractor, License EC13001410.
  • Licensed, insured and bonded.
  • We find the fault rather than replacing the breaker and hoping.
  • Honest about whether you need a breaker, a circuit repair or a panel.
  • Same day and after-hours response when the symptoms warrant it.
  • Residential and commercial.

Areas We Serve

We repair tripping breakers and faulty circuits throughout West Palm Beach, including downtown, Northwood, El Cid, Flamingo Park, SoSo and the neighborhoods along Okeechobee Boulevard, and across South Florida from Juno Beach to Fort Lauderdale: Palm Beach, Palm Beach Gardens, North Palm Beach, Jupiter, Riviera Beach, Lake Worth Beach, Greenacres, Wellington, Royal Palm Beach, Boynton Beach, Delray Beach and Boca Raton.

Frequently Asked Questions

  • Is it dangerous if my circuit breaker keeps tripping?

    The tripping itself is protective, so a breaker doing its job is a good sign rather than a bad one. What matters is why. An overloaded circuit is inconvenient and easily solved. A breaker that trips instantly with nothing plugged in, one that is hot, one accompanied by a burning smell or scorch marks, or a panel that buzzes means something is failing, and repeatedly resetting it is genuinely dangerous. The rule: reset once, and if it trips straight back, stop.

  • How many times can a breaker trip before it goes bad?

    There is no fixed number. Each trip puts mechanical and thermal stress on the internal mechanism, so a breaker that has tripped many times over the years is closer to failing than one that has not, and a worn breaker starts tripping below its rated current. If a breaker has a long history of tripping and now trips on loads it used to carry, the breaker itself is a reasonable suspect.

  • Should I replace a breaker that keeps tripping?

    Only after establishing why it trips. Swapping a breaker that is correctly reporting an overloaded circuit or a wiring fault removes the warning and leaves the hazard, which is the worst possible outcome. If the circuit is sound and the breaker trips below its rating, then yes, replacing it is the fix. Diagnosis first, replacement second.

  • How much does it cost to replace a circuit breaker?

    A standard single-pole breaker generally runs $150 to $300 installed, a double-pole or higher-amperage breaker $200 to $450, and GFCI or AFCI breakers $200 to $400. A diagnostic visit to trace a tripping circuit usually runs $125 to $250. Obsolete panels are quoted separately, because the problem there is breaker availability rather than labor.

  • Why does my breaker trip with nothing plugged in?

    Because the fault is in the fixed wiring, a permanently connected device, or the breaker itself rather than in anything you can unplug. With no load, an overload is ruled out, which leaves a short circuit, a ground fault or a failed breaker. All three need testing to locate, and the circuit should stay off until then.

  • My breaker will not reset at all. What now?

    First make sure you are resetting it properly: push the handle all the way to off until it clicks, then firmly to on. A handle left in the middle position will not restore power and this catches a lot of people. If it still will not hold, the fault is still live or the breaker has failed internally. Leave it off and call.

  • Why does my 20 amp breaker keep tripping?

    The same reasons as any other breaker: too much sustained load on that circuit, a short, a ground fault, a faulty appliance, or a worn breaker. Twenty-amp circuits serve kitchens, bathrooms, garages and workshops, so they tend to carry the high-draw appliances, which makes overload the most likely explanation. Breakers are designed to carry their rating continuously, so a 20 amp breaker tripping at a genuine 12 or 14 amps is telling you something other than overload.

  • Can I just put in a bigger breaker?

    No, and this is the most dangerous mistake on this subject. The breaker is sized to protect the wire behind it. Fitting a larger breaker lets that wire carry more current than it was designed for, and the wire has no way to tell you it is overheating inside a wall. If a circuit genuinely needs more capacity, it needs a new circuit with appropriately sized wire, not a bigger breaker on the old one.

  • Why does my GFCI breaker keep tripping?

    GFCI protection trips on very small current imbalances, so moisture is the usual cause, and in this climate it is constant: rain in an outdoor outlet, condensation in a disconnect, aging seals on pool or spa equipment, humidity in a garage. It can also be a genuine ground fault in an appliance or the wiring, or a GFCI device that has reached the end of its life. They should be tested periodically and they do not last forever.

  • My AFCI breaker trips for no reason. Can I swap it for a normal one?

    We would not recommend it. AFCI breakers detect the electrical signature of arcing, and some older appliances and motors produce signatures that read as arcing, which is the nuisance tripping people complain about. But occasionally the breaker is detecting exactly what it was built for. The right approach is to identify what is triggering it rather than remove the protection.

  • My main breaker keeps tripping. Is that different?

    Yes, and more serious. A main trips when the whole service is overloaded, when there is a fault on the distribution side, or when the main breaker itself is failing. It takes the entire property down rather than one circuit, and it should not be repeatedly reset. This one is worth calling about promptly rather than living with.

  • The breaker is warm. Is that normal?

    A breaker carrying a heavy load can be slightly warm. Hot to the touch is not normal, and neither is a warm panel door or a breaker noticeably hotter than its neighbors. Heat means resistance, and resistance in a panel means a loose or deteriorating connection releasing energy as heat inside a closed metal box. Call about it the same day.

  • Could my air conditioning be causing it?

    Very possibly, and it is one of the most common causes here. Condensers and air handlers are the largest loads in most homes, they run most of the year, and a failing compressor, a bad capacitor or a motor drawing excessive current will trip its breaker. If the breaker that trips is the one serving your AC, the problem may be the equipment rather than the electrical system, and we will tell you which.

  • My panel is a Federal Pacific. Does that change anything?

    Yes, and it is worth knowing. Federal Pacific Stab-Lok and Zinsco panels have a documented history of breakers failing to trip when they should, which is the opposite and far more dangerous failure. If you have one of these panels, a tripping breaker is the least of the issue, and replacement breakers for them are also difficult to source. Our Federal Pacific panel replacement page covers it properly.

Still Tripping?

If you have unplugged everything, reset it properly and it still trips, the fault is in the wiring, a fixed device or the breaker. That is where we come in. We find the cause rather than replacing parts until the symptom stops.

Call 561-582-2600 for breaker repair and circuit troubleshooting in West Palm Beach.

Emergency Electrical Control Panel Repair in West Palm Beach, FL
Scroll to Top